Development and validation of a capillary electrophoresis method for the determination of phenothiazines in human urine in the low nanogram per milliliter concentration range using field-amplified sample injection

A capillary zone electrophoresis (CZE) method with ultraviolet-visible detection has been established and validated for the determination of five phenothiazines: thiazinamium methylsulfate, promazine hydrochloride, chlorpromazine hydrochloride, thioridazine hydrochloride, and promethazine hydrochloride in human urine. Optimum separation was obtained on a 64.5 cm x 75 microm bubble cell capillary using a buffer containing 150 mM tris(hydroxymethyl)aminomethane and 25% acetonitrile at pH 8.2, with temperature and voltage of 25 degrees C and 20 kV, respectively. Naphazoline hydrochloride was used as an internal standard. Field-amplified sample injection (FASI) has been applied to improve the sensitivity of the detection. Considering the influence of parameters affecting the on-line preconcentration (nature of preinjection plug, sample solvent composition, injection times, and injection voltage) and due to the significant interactions among them, in this paper we propose for the first time the application of a multivariate approach to carry out the study. The optimized conditions were as follows: preinjection plug of water for 7 s at 50 mbar, electrokinetic injection for 40 s at 6.2 kV, and 32 microm of H3PO4 in the sample solvent. Also, a solid-phase extraction (SPE) procedure is developed to obtain low detection limits and an adequate selectivity for urine samples. The combination of SPE and FASI-CZE-UV allows adequate linearities and recoveries, low detection limits (from 2 to 5 ng/mL), and satisfactory precisions (3.0-7.2% for an intermediate RSD %).     

Conversion of sugarcane bagasse to carboxylic acids using a mixed culture of mesophilic microorganisms

Using the MixAlco process, biomass can be converted into carboxylic acids, which can be chemically converted into mixed alcohol fuels. This study focused on the use of countercurrent fermentation to anaerobically convert sugarcane bagasse and chicken manure to mixed carboxylic acids using a mixed culture of mesophilic microorganisms from terrestrial and marine sources. Bagasse was pretreated with lime to increase digestibility. The continuum particle distribution model (CPDM) simulated continuous fermentors based on data collected from batch experiments. This model saves considerable time in determining optimum operating conditions. For an 80% bagasse/20% chicken manure fermentation with terrestrial inoculum at a volatile solids loading rate (VSLR) of 7.36 g/(L of liquid·d) and a liquid residence time (LRT) of 8.88 d, total carboxylic acid productivity, total acid selectivity, and yield were 2.49 g/(L of liquid·d), 0.581 g of total acid/g of VS digested, and 0.338 g of total acid/g of VS fed, respectively, at a concentration of 18.7 g of total acid/L. At the same VSLR and LRT, fermentation with marine inoculum gave higher total acid productivity, total acid selectivity, and yield than fermentation with terrestrial inoculum. For an 80% bagasse/20% chicken manure fermentation with marine inoculum at a VSLR of 3.83 g/(L of liquid·d) and an LRT of 12.1 d, total carboxylic acid productivity, total acid selectivity, and yield were 1.38 g/(L of liquid·d), 0.667 g of total acid/g of VS digested, and 0.359 g of total acid/g of VS fed, respectively, at a concentration of 16.2 g of total acid/L.     

固相微萃取研究进展

对固相微萃取的发展背景，应用及其研究进展作了综述。引用文献 145篇。     

封闭压力酸溶-ICP-MS法分析地质样品中47个元素的评价

对封闭压力酸溶－ICP－MS法同时测定地质样品中47个元素的效果和适用范围进行了实测评价。并对溶样条件进行了优化。实验结果表明，HF－HNO3高温高压酸溶是一种有效的样品分解方法，在所测定的47个元素中，大部分元素如Li,Be,Ti,V,Mn,Co,Ni,Cu,Zn,As,Zr,Nb,Mo,Cd,In,Sn,Sb,Hf,Ta,W,Tl,Pb,Bi等在大多数标样中在三种取样量下都可以得到满意的回收率。而Sc,Cr,Ga,Y,REE,Rb,Cs,Sr,Ba,Th,U等元素在大部分样品中则随取样量减少，回收率上升，在一些样品中，当取样量降至25mg时，可以获得满意的回收率。用王水代替HNO3复溶残渣，利用氯离子的络合作用促进复溶，使许多元素的回收率有了明显的提高。     

气相色谱中保留值与进样量的关系

提出了测量气相色谱中吸附等温线的新方法，用不同进样量下测定的容量因子计算平衡时气-固两相组分浓度。利用建立的方法分别测量了正-己烷、正-壬烷和正-十一烷在邻苯二甲酸二辛酯(DOP)、阿皮松-L(Apiezon)和β，β′-氧二丙腈(ODPN)柱上的吸附等温线，讨论了色谱峰形状与吸附等温线的对应关系。研究了气相色谱中进样量对保留值的影响，利用佛伦德利希(Freundlich)吸附等温式导出了描述保留值与进样量关系的数学表达式。理论和实验证明，保留值与进样量具有良好的对数线性关系。     

原子吸收光谱法测定拉伸断口铬镍钼钛钢样品中主成分

研究了毫克级铬镍钼风样品中主成分镍的火焰原子吸收光谱法（FAAS法）和铬、钼、钒、钛、铝的塞曼恒温平台石墨炉原子吸收光谱法（ZSTPF－AAS法）。采用了微波溶样技术作为防污染样品预处理技术，采用石墨管硅涂层改进技术提高了仪器的测试精度。其中铬、镍、钼、钒、钛、铝的相对标准偏差分别为2.7%,0.97%,8.6%,7.3%,1.7%,7.3%。其加标回收率分别为96.5%,97%,96.7%,93%,98%,91%。通过分析，发现在较低温度下铬镍钼钛钢断面上有轻微的钼偏析现象，可能是拉伸断裂的主要化学影响因素。     

Developing a sequential injection-square wave voltammetry (SI-SWV) method for determination of atrazine using a hanging mercury drop electrode

This paper describes the development of a sequential injection analysis method to automate the determination of atrazine by square wave voltammetry exploiting the concept of monosegmented flow analysis to perform in-line sample conditioning and standard addition. To perform these tasks, an 800 μL monosegment is formed, composed by 400 μL of sample and 400 μL of buffer/standard solution. To obtain an efficient homogenization, the sample solution is divided in five zones intercalated by four zones of the Britton-Robinson buffer (pH 2.0) in presence of appropriate concentration of NaNO₃ and varying atrazine standard concentrations. This mixture zone is isolated from the carrier solution by two 100 μL air bubbles. After homogenization in an auxiliary reaction coil the mixture zone is injected toward the flow cell, which is adapted to the capillary of a hanging drop mercury electrode, at a flow rate of 50 μL s⁻¹. After a suitable delay time, the potential is scanned from −0.5 to −1.2 V versus Ag/AgCl using a frequency of 300 Hz and pulse height of 25 mV. The linear dynamic range is observed for atrazine concentrations between 1.16 × 10⁻⁷ and 2.32 × 10⁻⁶ mol L⁻¹, obeying the linear equation i_p = (−6.91 ± 0.07) × 10⁸[atrazine] + (4 ± 8), with r² = 0.9996, for which the slope is given in nA L mol⁻¹. The detection and quantification limits of the method are 2.1 × 10⁻⁸ and 7.0 × 10⁻⁸ mol L⁻¹, respectively. The sampling frequency is 37 h⁻¹, when the standard addition protocol is followed. This frequency can be increased to 42 h⁻¹ if the protocol to obtain in-line calibration curve is used for quantification. The method was applied for determination of atrazine in spiked river water samples and its accuracy was evaluated by comparison with the batch standard addition approach, which revealed that there is no evidence of statistically significant differences between the two methods.     

Evaluation of the calibration errors on cooling of a differential scanning calorimeter using different sets of standard metals

The temperature calibration on cooling of thermal analysis instruments is important for the accurate study of the non-isothermal crystallization kinetics of semi-crystalline polymers. In previous works, a methodology was proposed for performing the calibration on cooling of differential scanning calorimeters (DSCs) with standard metals, and the calibration errors were checked using transitions of high-purity liquid crystals. In this work, alternative, physically meaningful, procedures for carrying out the calibration on cooling are analyzed and validated. The calibration errors are evaluated also with liquid crystalline transitions, when the calibration is performed with standard metals, in a wide temperature range, and when due account is taken for the need of isothermal corrections to the temperature measurements. It is shown that any pair of standard metals may be used to calibrate on cooling, that the calibration errors increase for wider working temperature ranges and that, providing that certain conditions are fulfilled, both calibration procedures yield similar results.